HME# 400G627 Rev B 1/14/10 DX200 Wireless Intercom Operating Instructions
Base Station Features 524 25 26 27 28 29 30 31 32
SECTION 2. EQUIPMENT SETUP BATTERY CHARGER SETUP IMPORTANT! – Before installing the system, connect the AC power supply to the AC40A Battery Ch
BASE STATION SETUP The following description is for a basic, stand-alone DX200 system setup. Connections and setup for multiple, daisy-chained base
Interference Avoidance Interference, which may be heard in a headset as popping sounds, may occur whenever other equipment such as WI-FI systems, wir
Primary and Secondary Base Station Settings One base station must be designated as “primary” while the others are designated as “secondary”. You may
• To assign a number to a secondary base station and initialize it, press the REGISTER button on the secondary base. Pressing the button repeatedly
BELTPAC / WH200 HEADSET / SPEAKER STATION SETUP AND REGISTRATION The first time you operate the DX200 system, you must register each Beltpac, WH200
If registration is successfully completed: • A voice message in the headset will say “Power on, Beltpac #, Version #, Begin registration, Registrati
Set Up WH200 Headsets Before registering them, insert a fully charged battery in each Headset, with the metal contacts on the end of the battery inse
If the registration is successfully completed: • A voice message in the Headset will say “Power on, Headset #, Version #, Begin registration, Regist
Table of Contents SECTION 1. INTRODUCTION ...
Set Up Speaker Stations The WS200 Speaker Station can be used together with Beltpacs and WH200 All-in-one Headsets. It provides wireless communicati
Battery Operation Battery cover release latches If using the WS200 with battery power ― • Press down and pull out on the two battery cover releas
Register Speaker Stations The first time you operate a WS200, you must register it for use with a specific base station. The base station will then
If registration failed: • A voice message will say “Power on, Speaker, Version #, Begin registration, …” The ISO and IC lights on the WS200 will b
NOTICE You have completed the stand-alone system setup. The instructions under INTERCOM AND AUXILIARY EQUIPMENT SETUPS on the following pages
INTERCOM AND AUXILIARY EQUIPMENT SETUPS 24 25 26 27 28 29 30 31
The numbers (# ) below refer to items on the illustrations on page 20. Auxiliary Equipment Step 1. If using auxiliary equipment, such as another in
SECTION 3. EQUIPMENT OPERATION BASE STATION OPERATION Front Panel Controls, Indicators and Connector 1 3 4 2
The following base station indicators and controls are used only if 2-wire or 4-wire intercoms, or other auxiliary equipment is being used with the D
BELTPAC OPERATION 24Power lights The Beltpac control buttons have a snap action. They will activate when pressed firmly. Use your fingertips, no
FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
Volume Up/Down • Volume Up Adjustment — Each time you press and release the volume-up S button, you will hear a higher pitch beep in the earpiece
WH200 HEADSET OPERATION The Headset control buttons will activate when pressed lightly. Use your fingertips, not your fingernails, to press the bu
Volume Up/Down • Volume Up Adjustment — Each time you press and release the volume-up S button, you will hear a higher pitch beep in the earpiece
SPEAKER STATION OPERATION Headset connector Headset Connection If you are using a headset with the WS200, plug it into the headset connector.
29Routine Operation Power On/Off • To turn WS200 power on, press and release the POWER button. — Red lights will go on over the POWER, ISO and I
CALL Light Function If the CL200 (optional) Call Light button is pressed, or a call tone from an RTS or ClearCom intercom system is received through
SECTION 4. TROUBLESHOOTING If you are unable to correct any of the problems described below, contact your dealer for assistance. • Red light on ba
SECTION 5. TECHNICAL DATA EQUIPMENT SPECIFICATIONS Base Station GENERAL ⎯ Frequency Range: All, 2400 to 2483.5 MHz Low, 2401.92 to 2439.94 MHz
* 33NOTE: Communicators will follow the frequency range determined by the setting on the Base Station (e.g. All, Low or High). Speaker Station W
BLOCK DIAGRAM DX200 Base Station 34
Waste Electrical and Electronic Equipment (WEEE) The European Union (EU) WEEE Directive (2002/96/EC) places an obligation on producers (manufacturer
35
SECTION 1. INTRODUCTION The DX200 provides private, secure communication. Each base station can have up to a total of fifteen BP200 Beltpacs and/o
EQUIPMENT IDENTIFICATION The following equipment is standard with the DX200 Wireless Intercom System. As you unpack the equipment, check the enclos
MAIN EQUIPMENT FEATURES Beltpac Features 2 3 4 28 9 356 1
Speaker Station Features Left side panel Front panel
Kommentare zu diesen Handbüchern